Connect with us

HOWTO

What is Longboard Pumping and How to Pump on a Longboard

Published

on

Many of you might be aware of this technique called longboard pumping.

New riders still get confused and want to know what is longboard pumping and how to pump on a longboard.

Longboard pumping is a well know and fun technique that is performed by longboarders.

Pumping on a longboard is a substitute for kick pushing in which the rider on the board, without lifting his feet, can push himself in the forward direction.

This longboard pumping allows the rider to speed up his movements through this unique technique that is suitable for covering longer and shorter distances.

With the passage of time, longboard pumping is becoming popular, so in order to give you proper knowledge about this underrated technique, this article will clear all your aspects regarding this fun and cool longboarding trick.

What is Longboard Pumping?

Longboard pumping is basically the subclass of skateboarding.

It is the best way of covering long distances while providing a better experience of riding on flat ground to the rider.

The posture of the rider while longboard pumping is snake-like surfing, where the rider controls the movements through his weight.

The basic technique of this game is the weight balance that allows the rider to move in a zigzag and can gain momentum.

The rider uses their weight to move in the right or left position or back and forth by swaying his body.

As long as the board is in a balanced position on the flat ground, the rider can enjoy long and short-distance rides.

In Longboard pumping, pumping is a substitute way in which the rider drags himself on the longboard.

In this, the propelling engine acts as a weight that keeps the longboard on the specific track through coordinated swaying moments.

While lifting the front wheels of the longboard, the rider can gain speed easily while moving downhills.

How To Pump On A Longboard – Guide for beginners

The basic technique of having a better experience of longboard pumping is the balance of the rider’s weight on the flat ground.

The accurate shoulder position of the rider plays an important role in gaining the speed of the longboard.

The best way of riding is to act by throwing down the shoulders towards the heel side and toe side.

The basic mistake most riders do while longboard pumping is that they make use of their feet instead of shoulders to drive the pump.

So the best way of riding in a better way is to keep the body and shoulders in an accurate position for gaining speed as the legs alone are unable to generate enough driving force and momentum.

So for gaining the perfect momentum, the body and shoulders should be in a position to lead the movements.

Advertisement

In order to maintain the continuous rhythms of movement, the rider should keep his body in swinging motion continuously.

Pushing into every carve and digging in can further improve the longboard pumping.

The pressure exerted on toes and feet can help the rider to maintain the correct longboard position while riding on downhill or flat grounds.

Types of Longboards for Pumping

Junli 41 Inch Freeride Longboard Skateboard - Skateboard Cruiser for Cruising, Carving and Downhill
$150.65
  • TRUCKS: Highly responsive 7-inch aluminum alloy trucks and ultra-high elastic PU support pad, providing control and stability.
  • DECK: 41 IN long x 9.5 IN wide deck made of cold press 8-ply natural maple with max load weight 330Ibs; brushed black surface for antislip.
  • WHEELS: Durable 70mm X 51mm 80A PU wheels with rock finish, ABEC-11 high-speed bearings.
  • MANEUVERABILITY: Built for downhill, speed, and freestyle riding, wide turning radius, suitable for all age sports enthusiast groups.
  • PERFECT GIFT: Lightweight with shock absorb ring to guarantee smooth cruising.


11/17/2022 12:00 am GMT

There is a variety of pumping longboards that are suitable for beginners as well as professionals available in the market at different price ranges.

These longboards are specifically designed for users who love to go on long-distance rides in a much more adventurous way.

So following are the different types of longboards listed below:

  • Cruising longboards
  • Bamboo longboards
  • Fishtail longboards
  • Blunt longboards
  • Downhill
  • Pintail longboards
  • Drop Through
  • Carving longboards

Among these, the Downhill longboard is one of the most common types of longboard that are usually found in the streets.

These longboards are affordable in price and are found commonly anywhere in the market that is suitable for beginners.

So most of the users buy these longboards according to their level of usage and comfortability.

Efficient Riding

Obviously, the riding experience that the longboard provides to its rider is a type of efficient riding.

Longboard pumping is basically a technical game but once you get to know the basic tactics and techniques, you will be able to ride the longboard professionally without utilizing your energy.

Through centered wave-like body movements, the momentum is gained and the longboard is stabled. The right setup for pumping is also very important.

Trucks for Longboard Pumping

Trucks play the most important role in the setup of longboards as they are the most essential parts.

So trucks that have loose wiring along with higher turning angles are considered to be the best ones.

The most common type of pumping trucks is those that are thin and TKP.

Dadywheels Longboard Skateboard Trucks 7" with Bushings, Riser Pads and Hardware (Set of 2) Black
$69.99
  • Fit for a 9" longboard deck or wider for cruising, carving, and sliding.
  • Pack Contains: 2 pcs prebuilt trucks with 88a bushings, washers, and nuts; 2 pcs 3mm riser pads; 8 pcs 1.3" hardware screw and its nuts.
  • Reverse kingpin Truck Spec: 245mm/9.7" axle width; 180mm/7" hanger width; 64mm/2.5" height; 52°or 48°convertible baseplate angle; aluminum alloy material; hold up to 350 lbs.
  • Constructed from high-quality materials, suitable for pintail/drop through/freestyle longboard.


11/16/2022 02:10 pm GMT

In order to gain momentum, softer bushing trucks are recommended that allow better control while longboard pumping.

Body Workout

Longboard pumping is considered to be the best full-body workout as lots of muscles are involved.

As pumping involves pushing that works on the core of muscles in the body including the abs, legs, and lower back.

The most common problem faced by riders is Skogging. This problem can be reduced by using both legs for pushing which maintains proper balance while longboard pumping.

Pumping is also the best way of workout that involves an exercise of shoulders to legs.

FAQs About Longboard Pumping

What is pumping on a longboard?

Advertisement

Pumping is a type of skateboarding technique that involves speeding up the longboard while using the feet on it. It can also be done by moving the body back and forth or in the left and right positions.

Is longboarding tiring?

Yes, for beginners, longboarding is actually very tiring as it is a full-body workout that involves a broad range of muscles like abs, lower body, legs, and hips when moving on the downhill areas. On flat ground, it is basically a form of cardio that increases the strength of the heart and lung capacity.

Why longboarding is better than skateboarding?

Longboarding is suitable for long-distance rides because of the larger and smoother wheels. A skateboard has harder and smaller wheels that are just suitable for small-distance rides. That is why most people prefer longboarding over skateboarding because longboards are easy to ride.

What is the speed of the longboard on flat ground?

On flat ground, the minimum speed of the longboard is about 6 mph. Whereas while moving on the downhill sides, the speed increases that range from 50-65 mph.

Conclusion

Now that you have read the article about what is longboard pumping and how to pump on a longboard.

We hope that you will be looking forward to learning this technique and flaunting it in front of your friends.

Longboard pumping is the subclass of skating that is underrated. It involves moving the longboard in a forward direction while using the weight of the body of the rider.

In order to maintain the proper motion of the longboard, the positions of the shoulder and legs should be kept accurate.

Most of the riders make the mistake to use their legs instead of shoulders for leading the movements as legs alone cannot exert force.

So for proper longboard pumping, the body of the rider should move accurately in the zigzag direction.

And also back and forth to gain speed and to have stable momentum.

For this, the longboard trucks also play their part as they are an essential part of the setup.

They also help in gaining speed and maintaining the momentum of the longboard.

Advertisement
Click to comment

Leave a Reply

Your email address will not be published.

HOWTO

How to Clean Skateboard Wheels – Simple & Easy Tips For Skaters

Published

on

How to Clean Skateboard Wheels – Simple & Easy Tips For Skaters

Are you in search of techniques to help you clear the dirt from your amazing skateboard wheels? Has your skateboard speed reduced due to excessive use? This article will list the easy methods that will teach you How to Clean Skateboard Wheels easily by yourself. Skateboarding is a very popular and fun sport. To avoid the hassle of traffic, Skateboarders often use skateboards for commuting. Skateboarding can help with daily travel and save money and time.

People using skateboards for travel will accumulate dirt, hairs, thread, mud, and other obstacles in them. Dirt built up inside wheels slows the speed. Dirt removal increases the life of skateboards and saves money. Bearing balls also accumulate dirt easily as they have space between them. This dirt sticks and makes rolling hard. It will take much effort to propel the skate as wheels are hard and the ride with be bumpy.

Cleaning dirty skateboard wheels is a very easy process. Even beginners can easily learn to clean their skateboard wheels at home. The process is very simple and quick so anyone can learn it quickly. If you feel your skateboard speed is reduced or you are using your board excessively then its a clear signal that you need to clean the wheels of your skateboard.

To begin cleaning wheels firstly get all the required stuff ready. Keeping all the required stuff around will save a lot of hustle and make cleaning quick and easy.

List of things needed for cleaning skateboard wheels

  • A wrench or skate tool
  • Cleaning solution
  • Citrus spray cleaner
  • Toothbrush
  • lubricant oil
  • Pin
  • Cloth or tissue paper

Place all the necessary stuff near your skateboard and wear gloves if you feel necessary. Wheels and bearings have to be dipped in a solution so that dirt becomes soft. This step can cause skin sensitivity in some individuals or might cause dryness so those people can wear gloves for precaution. Follow the steps listed next orderly to have exceptionally clean wheels at the end.

Step1:

Position skateboard and remove wheels

Position the skateboard upside down. The deck riding surface will be facing down and the wheel will be up. Use a skate tool and remove the axle nut from the wheels. Remove all skateboard wheels using the same technique. Next, remove a washer. Place all-wheel parts in one place so that they are not lost and you can find them later easily. Nuts and washers are small and can be easily misplaced so it is better to keep a container near and place them in it.

Placing nuts and washers organized in a container will make it easy for you while reassembling. Some skateboards might not come with a skateboard tool so use a wrench instead. Select wrench size according to the wheel nut size. Remove nuts of all four wheels and next simply slide the wheels off from the truck axle.

Step2:

Removing bearing from wheels

This step will require some hard work. Some skate tools have a protruding end for extracting the bearing. The bearing press is a device used from removing or replacing the bearings at a shop. This can help a skater easily remove the bearing. Another technique to remove the bearing is to pry the wheel and bearing about a half-inch onto the axle. Next twist the angle of your wrist so that the bearing will come out. Bearings have to be separated from the wheel before cleaning as water exposure is harmful to the bearing. The bearing will rust and erode if exposed to water. Rusted bearings need to be replaced as they hinder the efficiency of the skateboard.

This step can be hard depending on the type of wheel. Screwdrivers can be used to extract bearings. Put a screwdriver in the middle of the wheel then put some pressure and pull the bearing out. Each wheel contains two bearings. An outer and an inner bearing with the spacer in between. Wheel bearings contain balls that roll inside the bearing.

Step3:

Washing the wheel

Skateboard Wheels have spaces that can accumulate anything from the surface you ride on. When wheels have accumulated dirt and sand and other things theyll slow down. Friction will be increased. Skater will have poor stability and balancing will be hard. Dirty wheels will stop skaters from long commuting at fast speed even tricks cannot be performed with dirty wheels. People using skateboards often should clean their skateboard wheels once a month or whenever they feel a need. Cleaning will give wheels a good long life and save you from buying a new pair of wheels.

After long use of skateboard, the wheels will have strongly attached dry dirt which will take time to remove. Prepare a soapy cleaning solution in a container. It takes time for the solution to dissolve the dirt so wheels should be left to stay in there for a while. Soak the wheels in that solution for half an hour. The dirt will have to soften after this time and then will be easily washed. Wash the wheels with enough water so all the mud and dirt are drained. The cleaning solution contains any detergent or soap used for cleaning dishes or other surfaces dissolved in warm water. This solution will act to dissolve the dirt which has become hard. When the dirt is softened by cleaning solution it will be easily drained by water.

Step4:

Scrubbing the wheels

Water will help remove all mud from wheels but to remove deep dirt, hair, threads, and other sticky stuff and for a thorough cleaning scrubbing should be done. Any brush can be used for scrubbing the wheels. Scrubbing will remove all remaining grime. Some brushes are designed to especially scrub wheels but if you dont have one then an old toothbrush or piece of cloth can do the same job. Due to the warm water solution, the entire dirt is soft now so brushing will be easy to remove whatever is left. While scrubbing pay attention to all the tiny spaces in the wheel as well where dirt may remain accumulated. Tiny spaces accumulate most dirt. With great attention scrub off all 4 wheels of the skateboard. Thorough scrubbing totally cleans the wheel surface, this will make the wheel surface look like new.

Step 5:

Drying the wheels

This step is very important and should be done very carefully. After scrubbing the skateboard wheels should be washed with a generous amount of water. When wheels are properly clean dry them using tissue papers or a piece of cloth. Dry the inner and outer surface of the wheel completely. When drying take away the wheels from the washing area or any other source of water. Place wheels in a completely dry environment rub the surface fully and try to remove maximum moisture. Let the wheels stay outside in the air for some time or it is better to keep wheels in some sunlight so that they are fully dry.

Never hurry to place the wheels back after cleaning. The moistened wheels will be heavy and so give a bad skateboard ride experience. Moisture affects other skateboard parts lethally especially wheel bearings and skateboard decks. The bearings will rust. The deck is also affected by moisture and may break due to repeated wetting. Similarly, if wheels are not dried properly the wet wheels will attract again. When wheels have properly dried assemble them to replace them in the skateboard.

Step 6:

Cleaning bearings

Bearings and wheels need to be separately washed because bearings are extremely water sensitive. Theyll easily rust when exposed to water. Bearings become useless after water exposure so while washing wheels keep bearings away at a dry place in some container. Cleaning bearings takes effort as each contains eight small bearing balls which can be misplaced easily. Remove the bearing shield using a pin and then use spray citrus cleaner to remove dirt. Lemon juice can be used also. Bearings can be soaked in alcohol or any other solvent and then after 2 minutes rinse with a solvent.

Dry the bearings in the air or with an air dryer. Wheel bearings need to be lubricated so that wheels will move more smoothly and efficiently. Any oil or grease available can be used. During lubrication it is a must to avoid over lubricating as over lubrication will increase friction and thus the temperature of the wheel bearing. With over greasing, pushing bearing elements while rolling becomes hard and takes more effort.

Advertisement

Bearings after cleaning should be dried quickly because they will rust if moist. It is best to rub off the wet surface and use a drying device for bearings. Drying in the air requires time which might affect the bearing. To know more about the bearings check out the list of Best Bearings available on the market.

Step 7:

Reassembling

Now all skateboard wheels and parts are clean and ready to be replaced. All the parts should be properly dried before placing back because moisture causes erosion and permanent damage. Firstly arrange the wheel bearings. The bearing shield should be put back on the surface of the bearing. The shield helps with keeping the lubricant inside and keep bearing balls rolling smoothly. Placing bearing back into wheel can be difficult for some so shopkeeper use bearing presser which will easily align the bearing in the wheel. To fit bearing into wheel first place one bearing on the truck axle and pry it off. Assembling the wheel is easy as one just needs to reverse the steps done earlier.

Push the wheel on the wheel axle and the bearing will fit in. After one bearing is placed, put a spacer then put the other bearing and push it similarly on the axle so it fits in. Use the same process for all four wheels. The bearings should be properly aligned and tightly fitted. After wheels and bearings are properly placed put the washer and axle nuts and screw the wheel nuts tightly.

To Sum Up

Anyone whether a pro skater or beginner can use these simple steps to clean the skateboard wheels. A Simple and easy method that gives better speed and stability. Give your wheels a good wash after a ride on a rough road or at the weekend after daily commuting for work or studies. Whether using a skateboard for transport or entertainment it doesnt matter, everyone should wash the board because it will not take much time although improve the performance extensively. Shops offer the same service but for a higher cost than cleaning at home.

As with all other devices used daily, skateboards also need maintenance. Skateboards are simple in design and can be easily managed at home after knowing some basic techniques. The steps to Dirty wheels not only affect the speed but the shape and appearance of wheels are affected very much. The wheels arent able to run smoothly over surfaces but instead, the skater will feel jerks. Wheels move smoothly and faster after cleaning and lubrication. Skaters requiring good speed and stability should clean their board often. Without proper maintenance the life span of the board will reduce, performing tricks will become difficult and the need to buy a new skateboard will cost a lot more money.

FAQs

How often should skateboard wheels be washed?

It mainly depends on individual conditions of use. If a skater is using a skateboard for daily commuting then frequent washing is necessary. Also if learning tricks at some dirty or muddy place then wash off immediately so dirt isnt accumulated or wheels will get damaged. For frequent users wash the skateboard once a month at least. People using skateboard occasionally or for only fun should wash off grime once in 3 to 4 months. Dirt if accumulated becomes hard and increases friction so it’s best to wash often.

Why cant wheel bearings be washed with wheels in the water?

Water bearings need to be separated from the wheel as they are water sensitive. Exposure to water even for a short duration will rust the bearings and theyll become useless. Bearings should only be washed with alcohol, solvent, or citrus spray. After rinsing the bearing should be dried promptly as any delay will cause it to rust and affect its smoothness. After drying and rinsing, bearings need to be lubricated as well so that friction is reduced and bearing balls roll smoothly.

Continue Reading

CULTURE

Watch How Old Decks Transformed into Custom Benches in this Video

Published

on

Watch Welcome Skate Shop staff and their friends turn old decks into custom benches in this video released by Vans as part of their efforts to promote artists and creativity. Welcome Skate Shop is based in Leeds, UK.

What’s great about this bench is that you can remove the top (the one made with old decks) and now you have a skateable bench. It has storage too so you have a place for your new skateboards or whatever needs storing.

A skateboarder may need to replace their decks in a few months to a year, depending on how hard they grind and how often they ride. Probably millions of skateboards are discarded each year and most of them end up in landfills.

This is just one of the ways worn-out decks can be repurposed. There are also initiatives to recycle and repurpose old wheels to keep them out of landfills.

Continue Reading

HOWTO

How To Install Skateboard Trucks? Step By Step Guide

Published

on

Not only the riding and doing tricks on a skateboard is fun, but the installation of its part is also exciting.

The structure of the skateboard is amazing as it will not only provide you with entertainment but also will let you understand how skateboards are made.

Just like other parts, the trucks of a skateboard are easy to install too so in this article we will talk about How to Install Skateboard trucks.

The installation process will let you learn and understand what steps to take to get trucks and ride the way you want.

Recommended
Havoc 5.0 Skateboard Trucks, Black

Pair of Havoc Aluminum Alloy Trucks. They come stock with a flush kingpin (less grinding hangups) and cast polyurethane bushings. The hanger Measures 5.0, or roughly 7.63". These will fit any board from 7.4" to 8".

Joining different skateboard parts together and making them ready for riding makes it more reliable for riding.

This is because you would know what joint you have made and how strong they are.

We have prepared this page to teach you the correct and easiest way of installing skateboard trucks on the skateboard.

Make sure you understand every step with proper understanding and have the right tools with you.

The whole process will only take around 25 minutes.

Furthermore, very few instruments are needed for proper installation, so you should not be worried about the tools.

How to Install Skateboard Trucks?

This installation of trucks on a skateboard method is the most effortless procedure that does not require many tools and can easily be performed within 20 minutes.

1. Assembling and Making the Truck Ready To Install

First, collect all the tools you need for the installation process.

Some of the necessary items are mentioned in further detail, which you should have before initiating the installation process.

Keep in mind that each skateboard will need two trucks.

There will be two wheels on each truck.

There is one hanger and one kingpin in each truck.

If you look into the further details, you will see two bushings, two washers, and one nut in each kingpin.

Some of the brands are manufacturing skateboards in which the trucks already contain assembled kingpins and hangers-on.

Now what you need to do is purchase a good quality washer, nuts, bolts, and bushings.

These things are readily available in the market, or you can also look for online purchases.

Now looking at the truck’s baseplate, it contains six holes of different sizes.

Advertisement

Four holes are comparatively smaller and constructed explicitly for bolts and nuts when attaching the bolt and base plate.

The two remaining holes are made for kingpins and hangers and are relatively more significant than the other four.

Now begin the assembling of the truck by sliding the hanger in the larger.

Try both holes but settle it in the one where it gets fixed.

Keep in mind to hold the hanger properly before you secure and tighten it with a kingpin.

Now you need to take the kingpin in your hand and look for the hole in the hanger.

Make sure not to push or force but slightly and smoothly enter the kingpin into this hanger hole and reach the second hole of the base plate.

You will also need a bushing and washer to thread from both sides of the hanger to assemble the kingpin.

Now you have to focus on the ends of the kingpin.

You need to take the washer and bushing in your hand and slide them into both ends individually.

After tightening and assembling all of these four tools in your kingpin, now it’s time to attach the kingpin to the base plate.

This is conveniently done by sliding it into the holes on the base plate.

Take a kingpin and locate it on the kingpin.

Tight this nut with the help of a wrench or a skate tool with you.

Make sure not to tighten them more than needed and not to leave them loose too.

This is important because in case you have pulled the kingpin nut very tightly, it will damage your board.

And thus the bushing will need replacement later on.

Follow the exact instructions mentioned above for assembling the second truck before installation.

Do not skip any step, as if your trucks are not correctly built; they will not be installed appropriately.

2. Installation of the Trucks on the Skateboard

You first need to make the holes in the new grip tape and, for this purpose, make use of something sharp-edged.

Advertisement

You can take a screwdriver for this purpose and poke eight holes in your grip tape.

This will take only a few seconds because the holes are already there on the board.

You only need to slide the sharp object which you have taken from the side of the board towards the tape so that it will get holes in it.

Turbo 9 x 33 Inch Skateboard Grip Tape Sheet Black
  • 9 x 33 Inch Fit Most Sizes of Skateboard, Cruiser or Scooter
  • Industry Standard 80 Grit Griptape
  • Easy Application on Any Skateboards
  • Adhesively Sticky in Cold and Hot Weathers
  • Fun Colors and Varies Design to Choose

This step is only for installing trucks on the new skateboard; otherwise, if you have an old skateboard and you are installing new trucks, then the holes would be present there already.

Make the holes just the way your board contains.

Your skateboard comprises two sets of four holes in them.

Initiate the process of joining the trucks with the board by inserting four bolts on one side of 4 holes from the top side of the board and four bolts on the other side of 4 holes.

Push them properly.

Push them the way you can see them if you turn the board upside down.

Remember to hold the board with one hand in case you are flipping it and checking it.

Now stick the bolts which are slid into the base plate from the small holes.

Remember and keep in mind that the kingpin side of the truck should be facing the inner side of the skateboard, and the hanger side should be facing the outside of the board.

Safely hold the base plate of the board and trucks in their places and put four nuts over four bolts.

Hold both nuts and bolts in their positions using recommended tools and then move one device by holding the other in its place tightly.

Tighten them but make sure not to tighten them more than the required force because if you have pulled them more than needed, it will break the board.

Repeat the similar process of installing the trucks on the skateboard with the exact instructions mentioned above.

Make sure you do not skip any option and always check that in the end, both of the sides of the trucks that contain kingpins are facing each other.

FAQs

Which way do you install skateboard trucks?

Make sure you install the trucks on the skateboard so that both bushing and kingpin face each other from inwards.

Remember to tighten the nuts and screws together slightly.

Advertisement

This will help you hold the trucks and the board in one place before you finally pull them.

And in this way, you will not feel any difficulty installing the skateboard trucks.

Why is my skateboard turning the wrong way?

This is possible in case you had tightened the bushings more than required when you were installing the truck in the initial stages.

You can fix this issue by assembling the bushings or replacing them with a good-quality ones.

Moreover, it’s not necessary to get a new bushing each time.

Instead, you can lose them a little if they are tight and use your skateboard.

Do you need speed washers?

Yes, these are essential tools that should be present in your skateboard.

This is because the primary purpose of a speed washer is to increase and enhance the speed and enhance the longevity of the bearings.

It is done by minimizing the friction between the hanger and the axle nuts.

Furthermore, speed washers help block the passage of dirt and dust to reach your bearings as this dust and dirt can affect the functioning of the trucks and wheels.

Conclusion

Skateboarding becomes more adventurous when you install the board on your own.

Installation of the skateboards involves not only installing tires on the board but also the proper installation of the trucks.

The aggregate installation of the trucks is essential because your board is based on the trucks, and if the trucks are not adequately placed, it means that your board is not stable and safe.

Before installing the trucks on your board, make sure you learn the proper procedure and follow it as it is.

The above-mentioned article contains the details of installing a truck on your skateboard and a step-by-step guide.

Make sure you understand the procedure correctly.

It will help you in assembling the trucks and installing them both.

Please do not skip any step as it will be dangerous for you as skipping a step affects the installation of the trucks.

Advertisement
Continue Reading

How To

HOWTO5 months ago

How to Clean Skateboard Wheels – Simple & Easy Tips For Skaters

Are you in search of techniques to help you clear the dirt from your amazing skateboard wheels? Has your skateboard...

CULTURE5 months ago

Watch How Old Decks Transformed into Custom Benches in this Video

Watch Welcome Skate Shop staff and their friends turn old decks into custom benches in this video released by Vans...

HOWTO6 months ago

How To Install Skateboard Trucks? Step By Step Guide

Not only the riding and doing tricks on a skateboard is fun, but the installation of its part is also...

HOWTO6 months ago

How Tight or Loose Should Skateboard Trucks Be? – Beginners’ Guide

Are you having trouble deciding how tight or loose your skateboard trucks should be? Well, you’ve come to the right...

HOWTO6 months ago

How to Fix Squeaky Skateboard Trucks – Guide For Beginners

Ever experienced a weird squeaky sound coming from the trucks of your skateboard while you are riding on it? It...

HOWTO7 months ago

Top 5 Best Solvents For Cleaning Skateboard Bearings – Reviews & Buyer’s Guide

Skateboard bearings need proper maintenance and if neglected, this can lead to lower speed and performance while skating over time....

HOWTO7 months ago

How to Tighten and Measure Skateboard Trucks – Easy Guide

Just bought new skateboard trucks for your skateboard or want to tighten the trucks on skateboards and now in search...

HOWTO8 months ago

12 Best Skateboards for Beginners in 2022 [ Reviews & Buying Guide ]

Ever seen those teenagers skating and doing tricks on the streets and in skate parks on their skateboards? They look...

Advertisement
Advertisement

Video Archive

Trending